My winter project

jasst

Member
Messages
2,313
not entirely sure whether in this instance these would of helped but worth knowing that you can get rivnuts which are extremely useful in these type of situations, got me out of a few jams, you can buy the fixing tool separately or as a kit and various thread sizes are available


View attachment 80107
Yes, have been looking at rivnuts, may well be utilised on some other areas.
 

jasst

Member
Messages
2,313
Not had a chance to do much lately, but have just managed to grab an hour to repair the heat shield, the repair patches are riveted and stuck on with 'tiger seal' so don't think they will be moving. Might not look that sightly, but is functional on a part no one will see unless they are crawling around under the car.
 

Attachments

  • 20210114_113355.jpg
    20210114_113355.jpg
    3.7 MB · Views: 46
  • 20210114_113339.jpg
    20210114_113339.jpg
    1.8 MB · Views: 55

Gp79

Member
Messages
1,393
Not had a chance to do much lately, but have just managed to grab an hour to repair the heat shield, the repair patches are riveted and stuck on with 'tiger seal' so don't think they will be moving. Might not look that sightly, but is functional on a part no one will see unless they are crawling around under the car.
That looks a good repair to me, be invisible with a bit of road dirt / oxidation.
 

jasst

Member
Messages
2,313
Well, I've had a look at the F1 pump motor this afternoon, and my idea of replacing just the motor while in situ, is a total non starter, so that may get postponed, on a more positive note, the 2 front bolts that hold heat shields on that snapped off :( have been drilled out and will be replaced by Rivnuts when I've bought the kit, this is favourite at the moment https://www.machinemart.co.uk/p/clarke-cht879-short-arm-hand-nut-riveter/ also replaced the centre section of stainless mesh with rivets and Tiger seal.
 

jasst

Member
Messages
2,313
Does the splitter need to be removed prior to removing the bumper?
Don't know if you have to, but I did hence the earlier post about broken fixings, one of the reasons for doing this work is so that if ever anything needs to be dismantled in future, it will come apart easily, as will all go back with stainless fixings, well greased.
 

CatmanV2

Member
Messages
48,547
Well, I've had a look at the F1 pump motor this afternoon, and my idea of replacing just the motor while in situ, is a total non starter, so that may get postponed,

I thought you could get to it from the spare wheel liner? In fact I'm absolutely sure you can.

C
 

jasst

Member
Messages
2,313
I thought you could get to it from the spare wheel liner? In fact I'm absolutely sure you can.

C
I thought you could get to it from the spare wheel liner? In fact I'm absolutely sure you can.

C
Not a chance, its forward of the spare wheel well, and no way can I get my hands in there, removing the whole pump would be easier, but to just remove the motor will involve removing the pump as well and then splitting it, and as its working, won't bother.
 

CatmanV2

Member
Messages
48,547
Not a chance, its forward of the spare wheel well, and no way can I get my hands in there, removing the whole pump would be easier, but to just remove the motor will involve removing the pump as well and then splitting it, and as its working, won't bother.

I an 100% sure it's been done on ML. Because it doesn't involve bleeding the F1 system. But I'm never going to be able to find the thread :(

C
 

Gp79

Member
Messages
1,393
I an 100% sure it's been done on ML. Because it doesn't involve bleeding the F1 system. But I'm never going to be able to find the thread :(

C
I hoped the same when I did mine, absolutely no room so did the complete pump/motor.
No issues with bleeding etc
Think it’s possible on certain Ferrari.
 

rs48635

Member
Messages
3,181
Not the thread I was looking for, and a different approach....


C
Page 5 of the ML article has post #90 by our own lozcb. Describes the job as quite a bit more awkward that the author of article. It is a DIY job but for the determined and committed.
"
Started attempting to change my F1 pump now seeing as nomorejags has made it sound relatively easy for the average astute guy who is prepared to have a go ,

Just to let you know im not exactly a novice , rebuilt my 4200 from salvage so i know a little of it workings, and all for saving a few quid (bucks) and enjoy tinkering with cars generally,

Easy it aint , he forgot to mention a few things which makes me wonder whether he actually did the complete repair or as i suspect played about with the already removed old pump. Start to finish extracting the old pump 28mins no way , to remove the the boot interior alone carefully would take that, which gives you access to the pump power connector , most important i would say other wise you have to cut the wires."
 

jasst

Member
Messages
2,313
Any one know which wires are the reversing light ones? or have a wiring diagram, need to connect up the reversing sensors, bumper is back on (sorry, forgot to take pics)
 

jasst

Member
Messages
2,313
Started phase 2 as most of phase 1 is complete, and that is to replace the airbox with a home made induction kit, following the lead from @2b1ask1 . Was fully expecting to have to remove the front bumper completely to be able to remove the old Airbus, but I have managed to do it without complete removal. Had to remove front under tray and near side headlight, and undo fixings attaching it to wing and the main 2 bolts and the bolts fixing it to front slam panel, this allowed enough movement of the wing to enable me to wiggle it out, so very pleased with myself. This is what is going in, in fact it is now in and fits very nicely in the space, looki g forward to some nice induction roar now.
 

Attachments

  • 20210123_144442.jpg
    20210123_144442.jpg
    2.2 MB · Views: 46
  • 20210123_152413.jpg
    20210123_152413.jpg
    2.3 MB · Views: 44
  • 20210123_152408.jpg
    20210123_152408.jpg
    1.6 MB · Views: 53

2b1ask1

Special case
Messages
20,220
As I understand it, have always done it that is:

Prep the car as you wish, isolate the battery (dial switch in boot) for 30 minutes.
Turn isolator back on, cycle the central locking and alarm.
Start engine with no throttle imput and idle for 10 minutes.
Swith off engine.
Restart and drive in your style for 20 mins +

Last one is the best bit, it and for me involves hooning the lanes with an ever bigger grin!

The system continues to learn your style of driving and I believe it also resets the altitude sensor as the base figure.
 

jasst

Member
Messages
2,313
My first attempt at machine polishing, then a coat of Harley's wax, not too bad.
 

Attachments

  • 20210411_123027_04.jpg
    20210411_123027_04.jpg
    93.3 KB · Views: 42
  • 20210411_123041_01.jpg
    20210411_123041_01.jpg
    124.8 KB · Views: 36
  • 20210411_123113.jpg
    20210411_123113.jpg
    82.3 KB · Views: 31
  • 20210411_123215.jpg
    20210411_123215.jpg
    84.5 KB · Views: 29
  • 20210411_123230.jpg
    20210411_123230.jpg
    90.5 KB · Views: 31
  • 20210411_123245.jpg
    20210411_123245.jpg
    85.3 KB · Views: 31